In short
- ISO 22734 is the international product standard for hydrogen generators that use water electrolysis, covering industrial, commercial and residential units. The current edition is ISO 22734:2019, and a revision is in development.
- It is a product standard: it tells the manufacturer how the packaged generator must be built, protected and tested. It does not design your plant, your hazardous-area layout or your pipeline.
- Its real value is as a shared language between buyer, OEM and certifier. Used well, it shortens commissioning and insurance discussions. Used as a box-ticking exercise, it leaves gaps at the interfaces where most incidents start.
What the standard covers
ISO 22734 applies to packaged or factory-matched systems that split water into hydrogen and oxygen using electricity, with alkaline (aqueous KOH) and proton exchange membrane (PEM) technologies firmly in scope. It sets requirements for construction, safety and performance, and defines the type and routine tests a generator must pass. It has been adopted regionally, for example as AS 22734 in Australia and as national modified versions in parts of Europe, so you will often see it referenced under a local prefix.
Out of scope, broadly: what happens downstream of the generator’s outlet flange. Compression, storage, dispensing and site-level piping are handled by other codes (ISO 19880 series for fuelling, ASME B31.12 or B31.3 for piping, NFPA 2 or local equivalents for site layout). Being clear on that boundary is the first engineering decision on any project.
The hazards it is built around
Rather than reading the clauses in order, it helps to see the standard as a response to five hazards that every electrolyser has:
- Hydrogen-oxygen mixing. Crossover through a membrane or diaphragm, or gas carry-over in separators, can push the hydrogen-in-oxygen concentration toward the lower flammability limit. The standard expects gas purity monitoring and defined shutdown actions well before that point.
- Hydrogen release into the enclosure. Leaks at fittings, stack seals or valves must be detected and diluted. This drives ventilation design, gas detection set points and the classification of the enclosure interior.
- Overpressure. Blocked outlets, failed regulators or runaway production need pressure relief sized for the credible worst case, discharged to a safe location.
- Electrical hazards. High DC currents at low voltage, plus mains-side power electronics, bring arc flash, insulation and earthing concerns, and possible ignition sources in hydrogen zones.
- Chemical hazards. In alkaline systems, hot concentrated KOH is corrosive and a significant personnel risk; in PEM systems, water quality and fluoride release from membranes matter for materials and maintenance.
Our earlier guide on oxygen-side management and safety in electrolyser plants goes deeper on the first of these, which is the one most often underestimated.
How it shapes design
Safety functions, not just safety devices
ISO 22734 pushes manufacturers to define each protective function (gas-in-gas shutdown, enclosure hydrogen detection, over-temperature, low electrolyte level, overpressure) and the safe state it drives the unit to. In practice that means a documented hazard analysis, a cause-and-effect matrix, and evidence that the control system performing those trips is adequately reliable, typically referencing functional-safety standards such as IEC 61508/61511 or ISO 13849. If an OEM cannot show you that matrix, that is a red flag regardless of what the certificate says.
Materials and pressure equipment
The standard expects materials compatible with hydrogen (including embrittlement considerations), with the electrolyte and with oxygen service. Pressure-containing parts are generally expected to comply with recognised pressure-equipment rules, so separators and vessels still go through ASME BPVC Section VIII, the EU Pressure Equipment Directive or the local equivalent. ISO 22734 does not replace those codes; it points to them.
Venting and relief
Hydrogen and oxygen vents must discharge where they cannot re-enter the enclosure, an air intake or each other. Relief devices must be sized for the governing scenario. From experience on pump and valve programmes under API 520/521, the weak point is rarely the valve itself: it is the outlet piping, the backpressure assumption and the discharge location relative to buildings, all of which sit at the generator-to-site interface.
Electrical and hazardous areas
Inside the enclosure, the manufacturer must either keep ignition sources out of zones where hydrogen can accumulate or use suitably protected equipment, with IEC 60079 being the usual reference. Ventilation is often used to reduce the zone classification, which makes ventilation failure itself a safety-critical event that must trip the unit.
Testing: what to expect at FAT
The standard distinguishes between type tests on a representative unit (done once, often witnessed by a certification body) and routine tests on every unit shipped. Typical elements include pressure and leak tests, verification that each safety trip actually fires at its set point, electrical safety tests, and performance checks of hydrogen output and purity against the rated values. Linking these to your own factory acceptance plan avoids paying twice; our guide to electrolyser FAT, SAT and performance test protocols shows how to structure that.
One practical point: type testing is usually done on a smaller or single-stack configuration. When an OEM scales to multi-megawatt, multi-stack skids, ask explicitly which conclusions carry over and which were re-verified. Gas crossover at low load, for instance, behaves differently in a larger system with shared separators.
Where ISO 22734 stops, and the gaps that follow
- Site integration. Separation distances, building design, fire protection and emergency response belong to site codes and your local authority. India’s PESO approvals, NFPA 2 in North America and national rules in Europe and the Middle East all apply on top.
- Large-scale plants. The standard grew up around packaged units. Hundreds-of-megawatt plants with centralised balance of plant raise process-safety questions (HAZOP, LOPA, QRA) that a product standard cannot answer.
- Hydrogen quality for end use. Purity for fuel cells is governed by ISO 14687, and green certification by schemes such as the EU RFNBO delegated acts or the Green Hydrogen Standard for India. ISO 22734 compliance says nothing about either.
- Newer technologies. AEM and membrane-less designs may fit only partly within the current text, which is one reason the revision matters. Expect manufacturers to justify deviations through risk assessment rather than clause-by-clause compliance.
The revision: why it matters
A new edition is being worked on through ISO/TC 197, with national bodies such as BSI running parallel projects (see the BSI standards development portal). Until it is published, contracts should name the 2019 edition explicitly and include a clause on how a mid-project revision will be handled. That avoids an argument at commissioning over which edition applies.
Checklist for engineers
- Define the scope boundary in writing: which flanges, cables and vents belong to the ISO 22734 package and which to site codes.
- Ask for the hazard analysis and cause-and-effect matrix, not just the certificate.
- Check gas-in-gas set points and the minimum turndown at which they were verified.
- Confirm pressure parts are stamped or certified under the pressure code your jurisdiction accepts.
- Review vent and relief discharge locations against your actual site layout.
- Verify enclosure ventilation failure is a trip, and how it is detected.
- Map type-test and routine-test evidence to your FAT plan to avoid duplicate testing.
- For scaled or multi-stack units, ask which type-test results were re-verified.
- Specify the standard edition in the contract and agree how revisions are handled.
- Keep ISO 14687 purity and green certification as separate deliverables.
For electrolyte-side equipment selection that feeds directly into these safety functions, see our guide on lye circulation pump selection for alkaline electrolysers.
Need a second pair of eyes?
Avoltium supports OEMs and project owners with electrolyser design reviews, DFMEA, standards gap assessments and FAT planning, drawing on hands-on development of alkaline electrolysers from 3 W to 10 kW. Explore our consulting services or get in touch at hello@avoltium.in.





