In short: The lye circulation pump is the only rotating machine that touches the electrolyte in an alkaline electrolyser, and it runs 8,000+ hours a year in hot, concentrated potassium hydroxide saturated with dissolved hydrogen and oxygen. Get the hydraulics, sealing, materials and turndown right and it disappears into the background. Get them wrong and it becomes the plant’s most frequent cause of unplanned trips. This guide walks through how we approach selection on real projects.
What the lye pump actually does
In a conventional pressurised alkaline system, 25–30 wt% KOH leaves the stack as a two-phase mixture, disengages in the hydrogen and oxygen separators, and drains back to a common or split return line. The circulation pump draws from the separator bottoms, pushes the liquid through a cooler and filter, and returns it to the stack inlet manifold. Its duties are three-fold:
- Heat removal: stack losses at 1.8–2.0 V per cell are rejected almost entirely through the electrolyte, so flow rate sets the temperature rise across the stack.
- Gas removal: enough velocity through the cell channels to sweep bubbles away and keep gas void fraction (and therefore ohmic loss) under control.
- Concentration and temperature uniformity: preventing hot spots and local KOH gradients that accelerate diaphragm and electrode degradation.
Because the pump also determines how much dissolved gas is carried from one separator side to the other in mixed-loop designs, it indirectly affects gas purity, which is a safety parameter. That is why the pump specification deserves more attention than a generic “chemical process pump” line item.
Sizing the duty point
Start from the stack heat balance, not from a vendor’s rule-of-thumb flow per square metre. A simple approach:
- Calculate heat generation at end-of-life voltage and maximum current density: Q = I × Ncells × (Vcell − Vthermoneutral), with Vtn ≈ 1.48 V.
- Pick an allowable stack temperature rise, typically 5–10 K. Smaller ΔT means better uniformity but higher flow and pump power.
- Flow = Q / (ρ × cp × ΔT), using properties of 30% KOH at operating temperature (density ~1,280 kg/m³, cp noticeably lower than water, around 3.0 kJ/kg·K).
- Check that the resulting channel velocity meets the stack OEM’s minimum for bubble removal; take the larger of the two flows.
Head is the sum of stack manifold and cell pressure drop (often dominant and strongly flow-dependent), cooler, filter, flow meter and control valve losses, plus elevation from separator to stack. Build the system curve at both beginning- and end-of-life: filters foul and cell channels can partially block with carbonate or nickel fines, so the system curve steepens over time.
One practical point: the pump operates at system pressure (commonly 15–30 bar g for pressurised alkaline), but the differential head is modest, often 2–5 bar. Do not confuse casing design pressure with differential head when reviewing datasheets. The casing, containment shell and flanges must be rated for full system pressure plus relief valve set-point margin.
NPSH: the hidden trap
Separator liquid is at saturation with respect to dissolved hydrogen or oxygen. Any pressure drop on the suction side lets gas come out of solution, which behaves like cavitation even though the liquid is far below its boiling point. Symptoms are noise, flow fluctuation and accelerated wear of impellers and bearings.
- Keep suction lines short, large-bore, and free of high points where gas can collect.
- Provide generous static head from separator low-low level to pump centreline; design to the low-low level, not the normal level.
- Add an NPSH margin well beyond the usual 0.5–1 m for clean water service. Many experienced teams target an NPSHa/NPSHr ratio of 1.5 or more for this duty.
- Avoid suction strainers with high clean pressure drop; place fine filtration on the discharge side instead.
Pump type and sealing
Almost every modern alkaline electrolyser uses a seal-less centrifugal pump, either magnetic drive (mag-drive) or canned motor. The reason is simple: hot caustic carrying dissolved hydrogen is exactly the fluid you do not want weeping past mechanical seal faces, and KOH crystallises on seal faces as it dries, causing rapid wear. Pump vendors such as Sundyne/HMD Kontro have published electrolyser-specific mag-drive offerings for this reason.
| Option | Strengths | Watch-outs |
|---|---|---|
| Mag-drive (metallic containment shell) | Standard motors, wide vendor base, easy motor replacement | Eddy-current losses heat the shell; product-lubricated bearings dislike dry running and gas slugs |
| Mag-drive (non-metallic shell) | No eddy losses, higher efficiency | Pressure and temperature limits; confirm rating at full system pressure |
| Canned motor | Compact, double containment, very low leakage risk | Motor cooled by process fluid, so temperature margin matters; motor and pump replaced as one unit |
| Double mechanical seal (API Plan 53/54) | Familiar to refinery maintenance teams | Barrier system complexity, crystallisation risk, more leak paths; rarely justified here |
Whichever seal-less type you choose, specify dry-run protection (power monitoring is more reliable than flow switches in two-phase service), a containment-shell temperature sensor, and bearing materials compatible with caustic, typically silicon carbide against silicon carbide.
Materials of construction
Austenitic stainless steels (316L) are widely used in KOH loops up to roughly 80–90 °C, but caustic stress corrosion cracking risk rises with temperature and concentration, and some OEMs move to nickel or nickel alloys for wetted parts in hotter, higher-concentration systems. Points to confirm with the stack OEM:
- Maximum operating and upset temperature, not just the normal value.
- Whether impellers, wear rings and shells need to match the rest of the loop to avoid galvanic issues.
- Elastomers: EPDM is common for caustic; avoid fluoroelastomers that degrade in hot alkali.
- Iron and chromium release limits, since dissolved metals can deposit on electrodes and change performance.
From valve and pump work at Weir Minerals and PSG Dover, the lesson that transfers directly is that material choice is a lifecycle decision. A cheaper casting that sheds metal ions into the electrolyte can cost far more in stack performance than it saves on the pump.
Turndown and renewable operation
Green hydrogen plants following solar or wind profiles run at 10–100% load and may hot-standby overnight. Heat generation scales roughly with the square of current, so lye flow requirements at part load are much lower, but minimum flow for gas sweep and separator level stability still applies.
- Variable speed drives are now the default. They avoid throttling losses and let the control system trade flow against temperature.
- Check the pump’s minimum continuous stable flow (MCSF) at the lowest operating speed. Mag-drive bearings and shells need a minimum flow for cooling.
- Consider a small minimum-flow recirculation line if the plant must hold at very low load for extended periods.
- For multi-stack plants, compare one large pump per stack versus shared headers. Shared headers save capital but make flow balancing between stacks a control problem.
Redundancy and availability
Loss of lye flow trips the stack within seconds because temperature and gas purity limits are quickly reached. A 2 × 100% configuration with auto-changeover is standard for anything above pilot scale. Make sure the standby pump is kept warm and primed, and that changeover logic is proven during FAT and SAT, not discovered during the first real trip.
Where VA/VE helps
Value engineering on the lye loop often finds savings in three places: right-sizing the pump to a realistic end-of-life system curve instead of stacking safety factors; standardising on one pump frame across stack sizes; and integrating cooler, filter and pump on a single skid to cut field piping. In our experience on membrane-less electrolyser development, simplifying the balance of plant was as important to CAPEX reduction as the stack itself. The same thinking applies to downstream steps like hydrogen gas drying.
Checklist for engineers
- Duty flow derived from end-of-life heat balance and checked against minimum channel velocity.
- System curves at beginning- and end-of-life, including fouled filter.
- Casing and containment rated for full system pressure plus relief margin.
- NPSHa calculated at separator low-low level with dissolved gas margin.
- Seal-less design (mag-drive or canned) with dry-run and shell temperature protection.
- Wetted materials and elastomers confirmed against max temperature and KOH concentration.
- VSD with verified MCSF at minimum speed; minimum-flow line if needed.
- 2 × 100% redundancy with tested auto-changeover.
- DFMEA entries for gas slugging, crystallisation during shutdown, and bearing wear.
- Spare parts and bearing inspection interval agreed with vendor before purchase.
Need a second pair of eyes?
Avoltium reviews balance-of-plant specifications, pump and valve datasheets, and DFMEAs for electrolyser developers and EPCs worldwide. Explore our consulting services or contact us at hello@avoltium.in.





